联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
地下金属探测器调试操作
地下金属探测器调试操作
Commissioning operation of underground metal detector
组装金属探测器
Assembly of metal detectors
组装金属探测器简单而且勿需任何特殊工具，只要按以下几个步骤做就可以了：
The assembly of metal detectors is simple and requires no special tools.
1.顺时针旋转金属杆上的锁结使它松动
The lock on the 1. clockwise rotation of the metal rod makes it loose
2.手持探测器站立，当探测盘与地面的距离在0.5至2英寸之间时，使胳膊自然地舒适地摆放，你可以依此调整探测杆的长短。
2. the handheld detector stands. When the distance between the probe and the ground is between 0.5 and 2 inches, the arm is placed naturally and comfortably, and you can adjust the length of the probe.
3.逆时针旋转锁结使它锁在固定的地方
3. counter clockwise rotation lock makes it locked in a fixed place
4.扭开探测盘上的螺母并把它和螺杆移开。插入金属轩并把它对准探测盘上的支架孔，把螺杆重新插入孔中，再把螺母上紧。
4. twist the nut on the probe and remove it from the screw. Insert the metal hall and position it on the support hole on the probe disc, insert the screw into the hole again, and tighten the nut.
5.把探测电缆缠绕在金属杆上。留下足够的长度使得在探测不平坦的地面时能够对探测盘进行高速。
5. the probe cable is twisted on a metal rod. Sufficient length is left to enable the detection disc to be high-speed at detecting uneven ground.
6.把探测盘的插头插入控制面板上的插座。注意确定插头上的芯对准了插孔。
6. insert the plug of the probe into the socket on the control panel. Notice that the core on the plug is aligned with the jack.
注意：探测盘插头只能以一种方式插入插座，不要用力插入以免造成损害。把探测盘电缆与探测盘断开，请抓住插头把其的拔下，勿要拔电缆线
Note: the probe plug can only be inserted into the socket in one way. Do not force insertion so as not to cause damage. Disconnect the probe cable from the detection panel. Please grab the plug and pull it out. Do not pull the cable.
7.松动探测盘上的螺母，以便于调整探测盘达到需要的角度（探测盘应该与地面平行）。把螺母拧到一个适当的程度便于探测盘旋转和振动。
7. loosening the nut on the detection disc, so as to adjust the probe to the required angle (the probe disk should be parallel to the ground). The nut is screwed to a proper degree to facilitate the detection of disc rotation and vibration.
Commissioning operation of underground metal detector
组装金属探测器
Assembly of metal detectors
组装金属探测器简单而且勿需任何特殊工具，只要按以下几个步骤做就可以了：
The assembly of metal detectors is simple and requires no special tools.
1.顺时针旋转金属杆上的锁结使它松动
The lock on the 1. clockwise rotation of the metal rod makes it loose
2.手持探测器站立，当探测盘与地面的距离在0.5至2英寸之间时，使胳膊自然地舒适地摆放，你可以依此调整探测杆的长短。
2. the handheld detector stands. When the distance between the probe and the ground is between 0.5 and 2 inches, the arm is placed naturally and comfortably, and you can adjust the length of the probe.
3.逆时针旋转锁结使它锁在固定的地方
3. counter clockwise rotation lock makes it locked in a fixed place
4.扭开探测盘上的螺母并把它和螺杆移开。插入金属轩并把它对准探测盘上的支架孔，把螺杆重新插入孔中，再把螺母上紧。
4. twist the nut on the probe and remove it from the screw. Insert the metal hall and position it on the support hole on the probe disc, insert the screw into the hole again, and tighten the nut.
5.把探测电缆缠绕在金属杆上。留下足够的长度使得在探测不平坦的地面时能够对探测盘进行高速。
5. the probe cable is twisted on a metal rod. Sufficient length is left to enable the detection disc to be high-speed at detecting uneven ground.
6.把探测盘的插头插入控制面板上的插座。注意确定插头上的芯对准了插孔。
6. insert the plug of the probe into the socket on the control panel. Notice that the core on the plug is aligned with the jack.
注意：探测盘插头只能以一种方式插入插座，不要用力插入以免造成损害。把探测盘电缆与探测盘断开，请抓住插头把其的拔下，勿要拔电缆线
Note: the probe plug can only be inserted into the socket in one way. Do not force insertion so as not to cause damage. Disconnect the probe cable from the detection panel. Please grab the plug and pull it out. Do not pull the cable.
7.松动探测盘上的螺母，以便于调整探测盘达到需要的角度（探测盘应该与地面平行）。把螺母拧到一个适当的程度便于探测盘旋转和振动。
7. loosening the nut on the detection disc, so as to adjust the probe to the required angle (the probe disk should be parallel to the ground). The nut is screwed to a proper degree to facilitate the detection of disc rotation and vibration.
